feat(units): read back every form the drawing writes

The readout learned to write lengths as 5'-6 1/2" and angles as
N 45d0'0" E, but typed input was still a bare parse::<f64>() — a
coordinate could be displayed and not entered. Give the formatters
their inverses.

parse_length takes feet and inches separated by a dash, a space, or
nothing, with the closing quote optional, and whole-plus-fraction in
any of those forms: 5', 60", 5'-9", 5'9-1/2, 9-1/2, 1/2. A leading
minus is a sign; the one inside 5'-9" is a separator, since after feet
there is nothing left to subtract from.

parse_angle reads the mark that says which convention an angle is in —
g for grads, r for radians, d/'/" for degrees-minutes-seconds, compass
letters for a surveyor's bearing — and reads a bare number in whichever
convention the drawing is set to.

ANGBASE and ANGDIR now apply, but only where they mean something. Which
way a thing points is measured from the drawing's zero and runs the way
it says; how wide an arc opens is the same number whatever zero is
counted from. format_direction and parse_direction are the pair for
directions, and the polar readout and polar input both go through them,
so the bearing shown is the bearing accepted. format_angle stays for
sizes, where applying a base angle would corrupt the value.

The command prompts follow the same rule, each classified rather than
swept: OFFSET distance, FILLET radius, CHAMFER distances, ARRAY and
MINSERT spacing, TRACE width, HELIX, and EXTRUDE height read lengths;
the four dimension text-rotation prompts, ARRAY's total angle and
INSERT's rotation read angles. MLINE's scale and INSERT's scale factor
are left alone — a multiplier has no unit to be written in. INSERT read
both through one parse; they are now separate.

The typed variants also take a decimal comma, which a single-value
prompt has no other use for. parse_length itself does not: inside a
coordinate the comma separates the axes.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>

src/app/helpers.rs

@@ -20,7 +20,13 @@ pub(crate) enum CoordKind {
 /// `distance<angle<elevation`.
 /// A leading `@` marks the value relative to the last point; a leading
 /// `#` forces absolute. Separators: comma or semicolon.
+///
+/// Each number is read by the same pair that writes it, so anything the
+/// drawing displays can be typed straight back: `5'-6 1/2"`, `9 1/2`,
+/// `@72'8"<n45d20'6"e`. Angles after `<` are directions, and so are counted
+/// from the drawing's zero and run the way it says.
 pub(crate) fn parse_coord(text: &str) -> Option<(glam::DVec3, CoordKind)> {
+    use crate::entities::common::{parse_direction, parse_length};
     let trimmed = text.trim();
     let (kind, rest) = if let Some(r) = trimmed.strip_prefix('@') {
         (CoordKind::Relative, r)
@@ -29,12 +35,13 @@ pub(crate) fn parse_coord(text: &str) -> Option<(glam::DVec3, CoordKind)> {
     } else {
         (CoordKind::Default, trimmed)
     };
-    let number = |value: &str| value.trim().parse::<f64>().ok();
     if let Some((distance, angles)) = rest.split_once('<') {
-        let distance = number(distance)?;
+        let distance = parse_length(distance)?;
         if let Some((azimuth, elevation)) = angles.split_once('<') {
-            let azimuth = number(azimuth)?.to_radians();
+            let azimuth = parse_direction(azimuth)?;
-            let elevation = number(elevation)?.to_radians();
+            // The rise out of the plane is a size, not a compass direction, so
+            // it is not counted from the drawing's zero.
+            let elevation = crate::entities::common::parse_angle(elevation)?;
             let horizontal = distance * elevation.cos();
             return Some((
                 glam::DVec3::new(
@@ -45,13 +52,12 @@ pub(crate) fn parse_coord(text: &str) -> Option<(glam::DVec3, CoordKind)> {
                 kind,
             ));
         }
-        let angle_and_z: Vec<&str> = angles.split(|c| c == ',' || c == ';').collect();
+        // A cylindrical `distance<angle,z` splits on the comma — but a
-        let (angle, z) = match angle_and_z.as_slice() {
+        // surveyor's bearing has none, so nothing here can eat one.
-            [angle] => (number(angle)?, 0.0),
+        let (angle, z) = match angles.split_once(|c| c == ',' || c == ';') {
-            [angle, z] => (number(angle)?, number(z)?),
+            Some((angle, z)) => (parse_direction(angle)?, parse_length(z)?),
-            _ => return None,
+            None => (parse_direction(angles)?, 0.0),
         };
-        let angle = angle.to_radians();
         return Some((
             glam::DVec3::new(distance * angle.cos(), distance * angle.sin(), z),
             kind,
@@ -59,9 +65,8 @@ pub(crate) fn parse_coord(text: &str) -> Option<(glam::DVec3, CoordKind)> {
     }
     let parts: Vec<f64> = rest
         .split(|c| c == ',' || c == ';')
-        .map(|s| s.trim())
+        .map(parse_length)
-        .filter_map(|s| s.parse().ok())
+        .collect::<Option<Vec<f64>>>()?;
-        .collect();
     match parts.as_slice() {
         [x, y] => Some((glam::DVec3::new(*x, *y, 0.0), kind)),
         [x, y, z] => Some((glam::DVec3::new(*x, *y, *z), kind)),

src/app/properties.rs

@@ -89,12 +89,9 @@ impl OpenCADStudio {
         // lengths/angles per LUNITS / LUPREC / AUNITS / AUPREC.
         {
             let h = &self.tabs[i].scene.document.header;
-            crate::entities::common::set_unit_context(crate::entities::common::UnitContext {
+            crate::entities::common::set_unit_context(
-                lunits: h.linear_unit_format,
+                crate::entities::common::UnitContext::from_header(h),
-                luprec: h.linear_unit_precision,
+            );
-                aunits: h.angular_unit_format,
-                auprec: h.angular_unit_precision,
-            });
         }
 
         let layer_names: Vec<String> = self.tabs[i]

src/app/view/mod.rs

@@ -1664,12 +1664,9 @@ impl OpenCADStudio {
                     // every refresh; the status bar redraws on its own schedule
                     // and cannot rely on that having happened.
                     crate::entities::common::set_unit_context(
-                        crate::entities::common::UnitContext {
+                        crate::entities::common::UnitContext::from_header(
-                            lunits: tab.scene.document.header.linear_unit_format,
+                            &tab.scene.document.header,
-                            luprec: tab.scene.document.header.linear_unit_precision,
+                        ),
-                            aunits: tab.scene.document.header.angular_unit_format,
-                            auprec: tab.scene.document.header.angular_unit_precision,
-                        },
                     );
                     let status_menu_data = crate::ui::statusbar::StatusMenuData {
                         layout_names: layout_names.clone(),

src/entities/common.rs

@@ -19,6 +19,27 @@ pub struct UnitContext {
     /// AUPREC — decimal places (angular)
     #[allow(dead_code)]
     pub auprec: i16,
+    /// ANGBASE — the world direction that a written angle of zero points in,
+    /// in radians. Applies to directions, never to angular sizes.
+    pub angbase: f64,
+    /// ANGDIR — true when written angles grow clockwise.
+    pub angdir_cw: bool,
+}
+
+impl UnitContext {
+    /// The settings as this drawing holds them. Every place that formats or
+    /// reads a number seeds the context from here, so none of them can be
+    /// working from a different idea of the drawing's conventions.
+    pub fn from_header(header: &acadrust::document::HeaderVariables) -> Self {
+        Self {
+            lunits: header.linear_unit_format,
+            luprec: header.linear_unit_precision,
+            aunits: header.angular_unit_format,
+            auprec: header.angular_unit_precision,
+            angbase: header.angle_base,
+            angdir_cw: header.angle_direction != 0,
+        }
+    }
 }
 
 thread_local! {
@@ -27,6 +48,8 @@ thread_local! {
         luprec: 4,
         aunits: 0,
         auprec: 0,
+        angbase: 0.0,
+        angdir_cw: false,
     }) };
 }
 
@@ -155,6 +178,205 @@ fn surveyor(value_rad: f64, prec: usize) -> String {
     format!("{pole} {} {side}", dms(bearing, prec))
 }
 
+// ── Reading numbers back ───────────────────────────────────────────────────
+//
+// The inverses of the formatters above, kept beside them so the pair cannot
+// drift: whatever the drawing writes, it can be handed back. Reading is the
+// looser of the two — it takes the shorthands people type as well as the full
+// forms — but it never accepts a form the drawing could not have produced.
+
+/// Read a length. Accepts plain decimals, feet-and-inches, and fractions.
+///
+/// Feet and inches separate with a dash, a space, or nothing, and the closing
+/// `"` is optional: `5'-9 1/2"`, `5' 9-1/2`, `5'9`, `9 1/2`, `1/2`, `60"` and
+/// `5'` all read. As with the architectural and engineering formats, the
+/// notation itself means one unit is one inch.
+///
+/// A leading `-` is a sign, but the `-` inside `5'-9"` is a separator — after
+/// feet there is nothing left to subtract from.
+pub fn parse_length(text: &str) -> Option<f64> {
+    let text = text.trim();
+    let (sign, rest) = match text.strip_prefix('-') {
+        Some(rest) => (-1.0, rest.trim_start()),
+        None => (1.0, text.strip_prefix('+').unwrap_or(text).trim_start()),
+    };
+    if rest.is_empty() {
+        return None;
+    }
+    let magnitude = match rest.split_once('\'') {
+        Some((feet, inches)) => {
+            let feet: f64 = feet.trim().parse().ok()?;
+            let inches = inches.trim().trim_end_matches('"').trim();
+            feet * 12.0 + parse_inches(inches.trim_start_matches('-').trim())?
+        }
+        None => parse_inches(rest.trim_end_matches('"').trim())?,
+    };
+    Some(sign * magnitude)
+}
+
+/// A count of inches: `9`, `9.5`, `1/2`, `9 1/2`, `9-1/2`, or nothing at all.
+fn parse_inches(text: &str) -> Option<f64> {
+    if text.is_empty() {
+        return Some(0.0);
+    }
+    let Some(slash) = text.find('/') else {
+        // No fraction, so any `-` left in here belongs to an exponent
+        // (`3.35E-01`) rather than to a separator.
+        return text.parse().ok();
+    };
+    let denominator: f64 = text[slash + 1..].trim().parse().ok()?;
+    if denominator == 0.0 {
+        return None;
+    }
+    // The numerator is the number nearest the slash; anything before the
+    // separator in front of it is a whole count of inches.
+    let head = text[..slash].trim();
+    let (whole, numerator) = match head.rfind([' ', '-']) {
+        Some(cut) => (head[..cut].trim(), head[cut + 1..].trim()),
+        None => ("", head),
+    };
+    let numerator: f64 = numerator.parse().ok()?;
+    let whole: f64 = if whole.is_empty() {
+        0.0
+    } else {
+        whole.parse().ok()?
+    };
+    Some(whole + numerator / denominator)
+}
+
+/// Read an angle, in radians.
+///
+/// A mark decides the convention — `g` grads, `r` radians, `d`/`'`/`"`
+/// degrees-minutes-seconds, compass letters a surveyor's bearing. A bare
+/// number is read in whatever convention the drawing is set to, so what the
+/// readout shows can be typed straight back.
+pub fn parse_angle(text: &str) -> Option<f64> {
+    let text = text.trim();
+    if text.is_empty() {
+        return None;
+    }
+    let upper = text.to_ascii_uppercase();
+    if upper.starts_with('N') || upper.starts_with('S') {
+        return parse_surveyor(&upper);
+    }
+    if let Some(body) = upper.strip_suffix('G') {
+        return Some((body.trim().parse::<f64>().ok()? * 0.9).to_radians());
+    }
+    if let Some(body) = upper.strip_suffix('R') {
+        return body.trim().parse().ok();
+    }
+    // Bare east/west read as the directions they name.
+    if upper == "E" {
+        return Some(0.0);
+    }
+    if upper == "W" {
+        return Some(std::f64::consts::PI);
+    }
+    if upper.contains('D') || upper.contains('°') || upper.contains('\'') {
+        return Some(parse_dms(&upper)?.to_radians());
+    }
+    let value: f64 = upper.parse().ok()?;
+    Some(match unit_context().aunits {
+        2 => (value * 0.9).to_radians(),
+        3 => value,
+        _ => value.to_radians(),
+    })
+}
+
+/// Degrees, minutes and seconds, each part optional after the first:
+/// `45`, `45d`, `45d20'`, `45d20'6"`.
+fn parse_dms(upper: &str) -> Option<f64> {
+    let (sign, rest) = match upper.strip_prefix('-') {
+        Some(rest) => (-1.0, rest.trim_start()),
+        None => (1.0, upper),
+    };
+    let (degrees, rest) = match rest.find(['D', '°']) {
+        Some(at) => (
+            rest[..at].trim().parse::<f64>().ok()?,
+            rest[at + rest[at..].chars().next()?.len_utf8()..].trim(),
+        ),
+        None => (rest.trim().parse::<f64>().ok()?, ""),
+    };
+    let (minutes, rest) = match rest.split_once('\'') {
+        Some((minutes, rest)) if !minutes.trim().is_empty() => {
+            (minutes.trim().parse::<f64>().ok()?, rest.trim())
+        }
+        Some((_, rest)) => (0.0, rest.trim()),
+        None => (0.0, rest),
+    };
+    let seconds = match rest.trim_end_matches('"').trim() {
+        "" => 0.0,
+        seconds => seconds.parse::<f64>().ok()?,
+    };
+    Some(sign * (degrees + minutes / 60.0 + seconds / 3600.0))
+}
+
+/// A surveyor's bearing — `N45D20'6"E`, or a lone `N` / `S` for due north and
+/// south. The inverse of [`surveyor`].
+fn parse_surveyor(upper: &str) -> Option<f64> {
+    let pole = upper.chars().next()?;
+    let body = upper[1..].trim();
+    if body.is_empty() {
+        return Some(if pole == 'N' {
+            std::f64::consts::FRAC_PI_2
+        } else {
+            3.0 * std::f64::consts::FRAC_PI_2
+        });
+    }
+    let side = body.chars().last()?;
+    if !matches!(side, 'E' | 'W') {
+        return None;
+    }
+    let bearing = parse_dms(body[..body.len() - 1].trim())?;
+    let degrees = match (pole, side) {
+        ('N', 'E') => 90.0 - bearing,
+        ('N', _) => 90.0 + bearing,
+        (_, 'W') => 270.0 - bearing,
+        _ => 270.0 + bearing,
+    };
+    Some(degrees.to_radians())
+}
+
+/// Read a length typed at a command prompt.
+///
+/// Same forms as [`parse_length`], plus the comma some keyboards put where a
+/// decimal point belongs. A prompt asking for one value has no other use for a
+/// comma, so taking it here is safe in a way it would not be inside a
+/// coordinate, where the comma separates the axes.
+pub fn parse_typed_length(text: &str) -> Option<f64> {
+    parse_length(&text.replace(',', "."))
+}
+
+/// Read an angle typed at a command prompt, in radians. Same forms as
+/// [`parse_angle`], with the same tolerance for a decimal comma.
+pub fn parse_typed_angle(text: &str) -> Option<f64> {
+    parse_angle(&text.replace(',', "."))
+}
+
+// ── Directions ─────────────────────────────────────────────────────────────
+//
+// A direction is not an angular size. Which way something points is measured
+// from ANGBASE and runs the way ANGDIR says, while how wide an arc opens is
+// the same number whatever zero the drawing counts from. Only directions go
+// through the pair below; `format_angle` and `parse_angle` stay for sizes.
+
+/// Write a world direction the way this drawing counts directions.
+pub fn format_direction(world_rad: f64) -> String {
+    let ctx = unit_context();
+    let relative = world_rad - ctx.angbase;
+    let shown = if ctx.angdir_cw { -relative } else { relative };
+    format_angle(shown.rem_euclid(std::f64::consts::TAU))
+}
+
+/// Read a direction written the way this drawing counts them, as a world
+/// angle.
+pub fn parse_direction(text: &str) -> Option<f64> {
+    let ctx = unit_context();
+    let typed = parse_angle(text)?;
+    let relative = if ctx.angdir_cw { -typed } else { typed };
+    Some(relative + ctx.angbase)
+}
+
 /// Two interior triangles covering a quad (flat list, 6 vertices) — the
 /// click-anywhere pick surface for frame-like entities (image, OLE frame,
 /// underlay, wipeout). Corners in ring order.

src/modules/annotate/aligned_dim.rs

@@ -168,7 +168,7 @@ impl CadCommand for AlignedDimensionCommand {
             self.text_angle = if t.is_empty() {
                 None
             } else {
-                t.parse::<f64>().ok().map(f64::to_radians)
+                crate::entities::common::parse_typed_angle(t)
             };
             self.awaiting_angle = false;
             return Some(CmdResult::NeedPoint);

src/modules/annotate/diameter_dim.rs

@@ -155,7 +155,7 @@ impl CadCommand for DiameterDimensionCommand {
             self.text_angle = if t.is_empty() {
                 None
             } else {
-                t.parse::<f64>().ok().map(f64::to_radians)
+                crate::entities::common::parse_typed_angle(t)
             };
             self.awaiting_angle = false;
             return Some(CmdResult::NeedPoint);

src/modules/annotate/linear_dim.rs

@@ -171,7 +171,7 @@ impl CadCommand for LinearDimensionCommand {
             self.text_angle = if t.is_empty() {
                 None
             } else {
-                t.parse::<f64>().ok().map(f64::to_radians)
+                crate::entities::common::parse_typed_angle(t)
             };
             self.awaiting_angle = false;
             return Some(CmdResult::NeedPoint);

src/modules/annotate/radius_dim.rs

@@ -157,7 +157,7 @@ impl CadCommand for RadiusDimensionCommand {
             self.text_angle = if t.is_empty() {
                 None
             } else {
-                t.parse::<f64>().ok().map(f64::to_radians)
+                crate::entities::common::parse_typed_angle(t)
             };
             self.awaiting_angle = false;
             return Some(CmdResult::NeedPoint);

src/modules/draw/draw/helix.rs

@@ -108,7 +108,7 @@ impl HelixCommand {
 
     /// Parse a positive distance from typed text; returns `None` on failure.
     fn parse_value(text: &str) -> Option<f64> {
-        text.trim().parse::<f64>().ok()
+        crate::entities::common::parse_typed_length(text)
     }
 }
 

src/modules/draw/draw/trace.rs

@@ -152,7 +152,7 @@ impl CadCommand for TraceCommand {
                 self.width_set = true;
                 return Some(CmdResult::NeedPoint);
             }
-            if let Ok(w) = t.parse::<f64>() {
+            if let Some(w) = crate::entities::common::parse_typed_length(t) {
                 if w > 0.0 {
                     self.width = w;
                     self.width_set = true;

src/modules/draw/modify/array.rs

@@ -177,7 +177,8 @@ impl CadCommand for ArrayRectCommand {
                 let row_sp = if t.is_empty() {
                     self.default_row_sp
                 } else {
-                    let v = t.parse::<f64>().unwrap_or(self.default_row_sp);
+                    let v = crate::entities::common::parse_typed_length(t)
+                        .unwrap_or(self.default_row_sp);
                     defaults::set_array_row_sp(v);
                     self.default_row_sp = v;
                     v
@@ -189,7 +190,8 @@ impl CadCommand for ArrayRectCommand {
                 let col_sp = if t.is_empty() {
                     self.default_col_sp
                 } else {
-                    let v = t.parse::<f64>().unwrap_or(self.default_col_sp);
+                    let v = crate::entities::common::parse_typed_length(t)
+                        .unwrap_or(self.default_col_sp);
                     defaults::set_array_col_sp(v);
                     v
                 };
@@ -341,7 +343,10 @@ impl CadCommand for ArrayPolarCommand {
                 let total_deg = if t.is_empty() {
                     self.default_angle
                 } else {
-                    let v = t.parse::<f64>().unwrap_or(self.default_angle);
+                    // Held in degrees, which is what the stored default is.
+                    let v = crate::entities::common::parse_typed_angle(t)
+                        .map(f64::to_degrees)
+                        .unwrap_or(self.default_angle);
                     defaults::set_array_p_angle(v);
                     v
                 };

src/modules/draw/modify/fillet.rs

@@ -1271,7 +1271,7 @@ impl CadCommand for FilletCommand {
                     self.resume_after_radius();
                     return Some(CmdResult::NeedPoint);
                 }
-                if let Ok(v) = t.replace(',', ".").parse::<f64>() {
+                if let Some(v) = crate::entities::common::parse_typed_length(t) {
                     if v >= 0.0 {
                         self.radius = v;
                         defaults::set_fillet_radius(v);
@@ -1293,7 +1293,7 @@ impl CadCommand for FilletCommand {
                 // "R 5.0" inline shorthand
                 if upper.starts_with('R') {
                     let body = t[1..].trim();
-                    if let Ok(v) = body.replace(',', ".").parse::<f64>() {
+                    if let Some(v) = crate::entities::common::parse_typed_length(body) {
                         if v >= 0.0 {
                             self.radius = v;
                             defaults::set_fillet_radius(v);
@@ -1687,7 +1687,7 @@ impl CadCommand for ChamferCommand {
                     self.step = ChamferStep::WaitingForDist2;
                     return Some(CmdResult::NeedPoint);
                 }
-                if let Ok(v) = t.replace(',', ".").parse::<f64>() {
+                if let Some(v) = crate::entities::common::parse_typed_length(t) {
                     self.dist1 = v.max(0.0);
                     defaults::set_chamfer_dist1(self.dist1);
                     self.step = ChamferStep::WaitingForDist2;
@@ -1703,7 +1703,7 @@ impl CadCommand for ChamferCommand {
                     self.resume_after_dist();
                     return Some(CmdResult::NeedPoint);
                 }
-                if let Ok(v) = t.replace(',', ".").parse::<f64>() {
+                if let Some(v) = crate::entities::common::parse_typed_length(t) {
                     self.dist2 = v.max(0.0);
                     defaults::set_chamfer_dist2(self.dist2);
                     self.resume_after_dist();
@@ -1727,7 +1727,7 @@ impl CadCommand for ChamferCommand {
                     let body = t[1..].trim();
                     let parts: Vec<f64> = body
                         .split_whitespace()
-                        .filter_map(|s| s.replace(',', ".").parse::<f64>().ok())
+                        .filter_map(crate::entities::common::parse_typed_length)
                         .collect();
                     if !parts.is_empty() {
                         if let Some(&v) = parts.first() {

src/modules/draw/modify/offset.rs

@@ -1004,7 +1004,7 @@ impl CadCommand for OffsetCommand {
                 if t.eq_ignore_ascii_case("t") || t.eq_ignore_ascii_case("through") {
                     return Some(self.advance_from_distance(None));
                 }
-                if let Ok(d) = t.parse::<f64>() {
+                if let Some(d) = crate::entities::common::parse_typed_length(&t) {
                     let d = d.abs().max(1e-9);
                     defaults::set_offset_dist(d);
                     return Some(self.advance_from_distance(Some(d)));
@@ -1021,7 +1021,7 @@ impl CadCommand for OffsetCommand {
                     return Some(CmdResult::NeedPoint);
                 }
                 if !t.is_empty() {
-                    if let Ok(d) = t.parse::<f64>() {
+                    if let Some(d) = crate::entities::common::parse_typed_length(&t) {
                         let d = d.abs().max(1e-9);
                         defaults::set_offset_dist(d);
                         *locked = Some(d);

src/modules/insert/insert_block.rs

@@ -220,16 +220,24 @@ impl CadCommand for InsertBlockCommand {
             }
             Step::FillAttr { .. } => Some(self.accept_attr_value(text)),
             Step::Point { .. } => {
-                // Typing the value awaited after a Scale / Rotate keyword.
+                // Typing the value awaited after a Scale / Rotate keyword. The
+                // two read differently: a scale is a plain multiplier with no
+                // unit to write it in, while a rotation is an angle and takes
+                // whichever convention the drawing is set to.
                 if let Some(kind) = self.awaiting {
-                    if let Ok(v) = text.trim().parse::<f64>() {
+                    match kind {
-                        match kind {
+                        AwaitKind::Scale => {
-                            AwaitKind::Scale if v != 0.0 => {
+                            if let Ok(v) = text.trim().parse::<f64>() {
-                                self.x_scale = v;
+                                if v != 0.0 {
-                                self.y_scale = v;
+                                    self.x_scale = v;
+                                    self.y_scale = v;
+                                }
+                            }
+                        }
+                        AwaitKind::Rotation => {
+                            if let Some(v) = crate::entities::common::parse_typed_angle(text) {
+                                self.rotation_rad = v;
                             }
-                            AwaitKind::Scale => {}
-                            AwaitKind::Rotation => self.rotation_rad = v.to_radians(),
                         }
                     }
                     self.awaiting = None;

src/modules/insert/minsert.rs

@@ -228,12 +228,12 @@ impl CadCommand for MinsertCommand {
                             }
                         }
                         ParamIdx::RowSpacing => {
-                            if let Ok(v) = typed.parse::<f64>() {
+                            if let Some(v) = crate::entities::common::parse_typed_length(typed) {
                                 self.row_spacing = v;
                             }
                         }
                         ParamIdx::ColumnSpacing => {
-                            if let Ok(v) = typed.parse::<f64>() {
+                            if let Some(v) = crate::entities::common::parse_typed_length(typed) {
                                 self.column_spacing = v;
                             }
                         }

src/modules/insert/solid3d_cmds.rs

@@ -77,9 +77,7 @@ impl CadCommand for ExtrudeCommand {
         self.step == ExtrudeStep::Height
     }
     fn on_text_input(&mut self, text: &str) -> Option<CmdResult> {
-        text.trim()
+        crate::entities::common::parse_typed_length(text)
-            .parse::<f64>()
-            .ok()
             .filter(|&h| h.abs() > 1e-6)
             .map(|h| CmdResult::ExtrudeEntity {
                 handle: self.target_handle,

src/ui/statusbar/mod.rs

@@ -574,13 +574,14 @@ fn format_coords(cursor: glam::DVec3, last: Option<glam::DVec3>, mode: i16, pick
             (true, Some(l)) => {
                 let d = cursor - l;
                 let dist = (d.x * d.x + d.y * d.y).sqrt();
-                // Kept in 0..2pi so the readout never shows a negative bearing,
+                // A bearing, so it is counted from the drawing's zero and runs
-                // then handed over in radians for AUNITS / AUPREC to format.
+                // the way the drawing says — and comes back out in the same
-                let ang = d.y.atan2(d.x).rem_euclid(std::f64::consts::TAU);
+                // form the polar input accepts.
+                let ang = d.y.atan2(d.x);
                 format!(
                     "{} < {}",
                     len(dist),
-                    crate::entities::common::format_angle(ang)
+                    crate::entities::common::format_direction(ang)
                 )
             }
             _ => abs(cursor),

src/ui/window/drawing_units.rs

@@ -311,6 +311,13 @@ fn with_context(state: &State, body: impl FnOnce() -> String) -> String {
         luprec: state.linear_precision,
         aunits: state.angular_format,
         auprec: state.angular_precision,
+        angbase: state
+            .base_angle
+            .trim()
+            .parse::<f64>()
+            .unwrap_or(0.0)
+            .to_radians(),
+        angdir_cw: state.clockwise,
     });
     let out = body();
     set_unit_context(previous);